+90 850 242 96 90

Domestic Flight Control Board

Agno Horizon · Flight Control Hardware

Domestic Flight Control Board for Unmanned Aerial Vehicles

The flight control board is the onboard electronic unit that processes data from the vehicle's sensors, estimates position and attitude, and generates the control commands sent to motors and servos. Through the domestic flight control board R&D program launched in 2024, AGNOBİL is developing this unit with its own engineering team, from printed circuit board (PCB) design to embedded software.

  • Domestic PCB design
  • Sensor fusion
  • Real-time control
  • Failsafe
  • MAVLink telemetry
  • Horizon Core firmware
Definition

What Does a Flight Control Board Do?

Described as the "brain" of an unmanned aerial vehicle, the flight control board keeps the vehicle stable in the air, makes it respond correctly to pilot or mission commands and ensures safe behavior in unexpected situations.

The board calculates the vehicle's instantaneous state by combining data from the inertial measurement unit (IMU, consisting of accelerometer and gyroscope), barometer, magnetometer and GNSS receiver. This state information feeds the control algorithms; the outputs are sent to motor drivers and servos. At the same time, telemetry data is sent to the ground control station.

  • Sensing: timed and synchronized reading of sensor data
  • Estimation: calculating attitude, altitude and position through sensor fusion
  • Control: reaching the target state through closed-loop control
  • Safety: defined behaviors in case of link loss, low battery and sensor failure
Flight control board block diagramData flow from the sensors to the processor, and from the processor to motor and servo outputs, telemetry and the mission computer. FLIGHT CONTROL BOARD Main processor (MCU)Real-time control loop Stateestimation Failsafe &logging Power management and monitoringSupply · voltage/current measurement IMU (accelerometer, gyroscope) Barometer Magnetometer (compass) GNSS receiver Motor / servo outputs Telemetry (MAVLink) RC receiver input Flight control computer Conceptual block diagram; component selection is determined per project.
Data flow on the flight control board from sensor data to control output.
Hardware Design

Engineering Approach in Domestic PCB Design

Sensor Placement and Vibration

The quality of flight control depends heavily on clean sensor data. IMU position, the effect of mechanical vibration and thermal variations are addressed at the very start of the board layout.

Power and Signal Integrity

Electrical noise from motor drivers is separated from sensitive sensor lines. The supply line is monitored; voltage and current information is used both in the control logic and in telemetry.

Communication Interfaces

The board is designed to communicate over standard serial interfaces with peripherals such as the telemetry modem, RC receiver, GNSS module, external sensors and the flight control computer.

Adaptability per Project

The number of connections, form factor and peripheral needs vary from platform to platform. The board architecture aims for a modular structure that can be adapted to different mission profiles.

Hardware + Software

Board and Firmware from the Same Team

The flight control board is developed together with the Agno Horizon Core autopilot and firmware layer. The team designing the hardware defines the timing, interrupt and driver requirements of the embedded software at the design stage. This way, incompatibilities between hardware and software are resolved before reaching the field.

The board communicates with Agno Horizon GCS over the MAVLink protocol; mission plan upload, parameter management and live telemetry are handled through the ground control software.

Development Process

From Design to Validation

  1. Requirements AnalysisPlatform type, mission profile, peripherals and environmental conditions are defined.
  2. Schematic and PCBComponent selection, circuit schematic and board layout are prepared.
  3. PrototypePrototype boards are produced and electrical tests are performed.
  4. Firmware IntegrationDrivers, sensor fusion and control loops are adapted to the board.
  5. ValidationBehavior is validated through simulation, bench tests and controlled flight trials.
Technical Scope

Flight Control Board Scope

ProductAgno Horizon flight control board (FCC)
Target PlatformsMultirotor, fixed-wing and VTOL unmanned aerial vehicles; R&D and prototype platforms
Sensor SuiteIMU (accelerometer, gyroscope), barometer, magnetometer, external GNSS interface
Embedded SoftwareAgno Horizon Core autopilot and firmware layer
CommunicationMAVLink-based telemetry and command; data exchange with the flight control computer
Ground SegmentAgno Horizon GCS and ground control stations
Development ModelBoard architecture developed within R&D and adaptable per project

Detailed technical specifications are determined according to project requirements and shared on request. For past notes on the board's R&D process, see the domestic flight control board R&D page.

Frequently Asked Questions

Questions and Answers

What is a domestic flight control board?

It is an onboard electronic board, designed, laid out and programmed domestically, that processes the sensor data of an unmanned aerial vehicle and generates control commands. The Agno Horizon flight control board is developed by AGNOBİL within this scope.

What is the difference between a flight control board and a flight control computer?

The flight control board is the real-time control unit that ensures the vehicle's stability and basic flight. The flight control computer runs higher-level tasks such as mission management, autonomous decision-making and image processing, and works together with the flight control board.

Which vehicle types can it be used on?

The board architecture is designed for multirotor, fixed-wing and VTOL unmanned aerial vehicles and R&D platforms. Platform-specific adaptation needs are evaluated on a project basis.

Is it compatible with Agno Horizon GCS?

Yes. The flight control board communicates with Agno Horizon GCS over the MAVLink protocol; mission upload, parameter tuning and live telemetry are handled through the ground control software.

Is project-specific board design available?

Since form factor, connection needs and peripherals vary by platform, the board architecture can be adapted per project. Requests are evaluated after a preliminary technical meeting.

Horizon Ecosystem

Related Technologies

Let's Discuss Your Flight Control Board Project

Share your platform, mission profile and integration needs, and let our hardware and firmware team evaluate them.

Go to the contact form

Contact Us About the Flight Control Board

    Please fill out the message section as clearly and detailed as possible.

    Alternatively, you can send an email to [email protected].