Domestic Flight Control Board for Unmanned Aerial Vehicles
The flight control board is the onboard electronic unit that processes data from the vehicle's sensors, estimates position and attitude, and generates the control commands sent to motors and servos. Through the domestic flight control board R&D program launched in 2024, AGNOBİL is developing this unit with its own engineering team, from printed circuit board (PCB) design to embedded software.
What Does a Flight Control Board Do?
Described as the "brain" of an unmanned aerial vehicle, the flight control board keeps the vehicle stable in the air, makes it respond correctly to pilot or mission commands and ensures safe behavior in unexpected situations.
The board calculates the vehicle's instantaneous state by combining data from the inertial measurement unit (IMU, consisting of accelerometer and gyroscope), barometer, magnetometer and GNSS receiver. This state information feeds the control algorithms; the outputs are sent to motor drivers and servos. At the same time, telemetry data is sent to the ground control station.
- Sensing: timed and synchronized reading of sensor data
- Estimation: calculating attitude, altitude and position through sensor fusion
- Control: reaching the target state through closed-loop control
- Safety: defined behaviors in case of link loss, low battery and sensor failure
Engineering Approach in Domestic PCB Design
Sensor Placement and Vibration
The quality of flight control depends heavily on clean sensor data. IMU position, the effect of mechanical vibration and thermal variations are addressed at the very start of the board layout.
Power and Signal Integrity
Electrical noise from motor drivers is separated from sensitive sensor lines. The supply line is monitored; voltage and current information is used both in the control logic and in telemetry.
Communication Interfaces
The board is designed to communicate over standard serial interfaces with peripherals such as the telemetry modem, RC receiver, GNSS module, external sensors and the flight control computer.
Adaptability per Project
The number of connections, form factor and peripheral needs vary from platform to platform. The board architecture aims for a modular structure that can be adapted to different mission profiles.
Board and Firmware from the Same Team
The flight control board is developed together with the Agno Horizon Core autopilot and firmware layer. The team designing the hardware defines the timing, interrupt and driver requirements of the embedded software at the design stage. This way, incompatibilities between hardware and software are resolved before reaching the field.
The board communicates with Agno Horizon GCS over the MAVLink protocol; mission plan upload, parameter management and live telemetry are handled through the ground control software.
From Design to Validation
- Requirements AnalysisPlatform type, mission profile, peripherals and environmental conditions are defined.
- Schematic and PCBComponent selection, circuit schematic and board layout are prepared.
- PrototypePrototype boards are produced and electrical tests are performed.
- Firmware IntegrationDrivers, sensor fusion and control loops are adapted to the board.
- ValidationBehavior is validated through simulation, bench tests and controlled flight trials.
Flight Control Board Scope
| Product | Agno Horizon flight control board (FCC) |
|---|---|
| Target Platforms | Multirotor, fixed-wing and VTOL unmanned aerial vehicles; R&D and prototype platforms |
| Sensor Suite | IMU (accelerometer, gyroscope), barometer, magnetometer, external GNSS interface |
| Embedded Software | Agno Horizon Core autopilot and firmware layer |
| Communication | MAVLink-based telemetry and command; data exchange with the flight control computer |
| Ground Segment | Agno Horizon GCS and ground control stations |
| Development Model | Board architecture developed within R&D and adaptable per project |
Detailed technical specifications are determined according to project requirements and shared on request. For past notes on the board's R&D process, see the domestic flight control board R&D page.
Questions and Answers
What is a domestic flight control board?
It is an onboard electronic board, designed, laid out and programmed domestically, that processes the sensor data of an unmanned aerial vehicle and generates control commands. The Agno Horizon flight control board is developed by AGNOBİL within this scope.
What is the difference between a flight control board and a flight control computer?
The flight control board is the real-time control unit that ensures the vehicle's stability and basic flight. The flight control computer runs higher-level tasks such as mission management, autonomous decision-making and image processing, and works together with the flight control board.
Which vehicle types can it be used on?
The board architecture is designed for multirotor, fixed-wing and VTOL unmanned aerial vehicles and R&D platforms. Platform-specific adaptation needs are evaluated on a project basis.
Is it compatible with Agno Horizon GCS?
Yes. The flight control board communicates with Agno Horizon GCS over the MAVLink protocol; mission upload, parameter tuning and live telemetry are handled through the ground control software.
Is project-specific board design available?
Since form factor, connection needs and peripherals vary by platform, the board architecture can be adapted per project. Requests are evaluated after a preliminary technical meeting.
Related Technologies
Autopilot & Firmware
Horizon Core: control algorithms, flight modes and embedded software.
Explore →Flight Control Computer
Onboard computing unit for mission, autonomy and image processing.
Explore →Agno Horizon GCS
Mission planning, telemetry and vehicle management software.
Explore →Communication & Command Control
Data link, network architecture and multi-domain command and control.
Explore →Let's Discuss Your Flight Control Board Project
Share your platform, mission profile and integration needs, and let our hardware and firmware team evaluate them.