+90 850 242 96 90

UAV Autopilot and Flight Control Firmware Software

Agno Horizon Core · Embedded Software

Autopilot and Flight Control Firmware Layer

Agno Horizon Core is the embedded software layer that runs on the flight control board and manages the vehicle's sensing, estimation, control and communication functions. The autopilot enables the vehicle to follow a defined route without pilot intervention, maintain its altitude and speed, and execute mission steps in sequence.

  • Autopilot
  • Embedded software
  • Sensor fusion
  • Flight modes
  • Failsafe
  • Parameter management
  • MAVLink
Definition

What Does UAV Autopilot Software Do?

Autopilot software is embedded software that manages the flight of an unmanned vehicle with defined rules and control algorithms. Flight control firmware is the complete body of this software running on the hardware.

The firmware reads sensors at specific frequencies, estimates the vehicle's state by fusing the data, generates motor and servo commands through nested control loops, and reports all these processes to the ground control station as telemetry. Mission plans, flight modes and safety behaviors are also defined in this layer.

Agno Horizon Core is developed with a layered architecture: hardware-dependent drivers are kept in the lower layer, and control and mission logic are abstracted from the hardware. This approach makes it easier to adapt the same software core to different boards and platforms.

Agno Horizon Core firmware layersFirmware software stack from hardware abstraction to the mission and communication layer. Communication layer · MAVLink telemetry and command · parameter management Mission and flight modes · waypoint · return · landing · failsafe Navigation and position control Attitude and rate control loops State estimation · sensor fusion Hardware abstraction · sensor and output drivers · timers Flight control board hardware TOPBOTTOM
Agno Horizon Core firmware software stack: from hardware abstraction to the communication layer.
Capabilities

Core Components of the Firmware

State Estimation

Fusing IMU, barometer, magnetometer and GNSS data to produce attitude, velocity and position information.

Control Loops

Cascaded control structure for attitude, velocity and position; control parameters tunable to platform dynamics.

Flight Modes

Defined flight modes from manual and stabilized to automatic mission, position hold, return and landing.

Failsafe Management

Defined safe behaviors in situations such as communication loss, low battery, GNSS loss and sensor inconsistency.

Parameter Management

Reading, changing and saving control, sensor and safety settings through the ground control software.

Logging and Analysis

Recording flight data; enabling post-flight performance and event analysis.

Validation

Simulation-Based Development

In firmware development, changes are first validated in a simulation environment. With software-in-the-loop (SITL) simulation, control logic, mission flow and failsafe behaviors are tested without putting a real vehicle at risk. Footage from a SITL flight test performed with Agno Horizon GCS is available on the GCS page.

  1. SimulationValidating control and mission logic in a SITL environment
  2. Bench TestSensor, output and communication tests on the board
  3. Controlled FlightParameter tuning and behavior validation
Ecosystem

Horizon Core and Other Components

Hardware It Runs OnAgno Horizon flight control board
Ground SegmentMission, parameter and telemetry management via Agno Horizon GCS
Upper LayerAutonomous mission and image processing integration with the flight control computer
ProtocolMAVLink-based telemetry and command
DownloadCurrent versions of Agno Horizon software on the download page
Frequently Asked Questions

Questions and Answers

What is UAV autopilot software?

It is embedded software that manages the flight of an unmanned vehicle with control algorithms and defined rules. It enables the vehicle to follow its route, maintain altitude and speed, execute mission steps and behave safely in unexpected situations.

What is the difference between firmware and autopilot?

Firmware is the entire software running on the flight control board: it includes the driver, estimation, control, mission and communication layers. Autopilot refers to the functions of this software that automatically manage the flight.

What is Agno Horizon Core?

Agno Horizon Core is the name of the autopilot and firmware layer that AGNOBİL develops for the Agno Horizon flight control board.

How is a firmware update performed?

Firmware and parameter operations are carried out through the ground control software. Current software versions are available on the Agno Horizon download page.

Can it be adapted to different platforms?

Thanks to the layered architecture, control and mission logic are abstracted from the hardware; control parameters and flight modes can be adapted to platform dynamics.

Horizon Ecosystem

Related Technologies

Let's Talk About Your Autopilot and Firmware Needs

Share your platform and mission scenario, and let our embedded software team carry out a technical evaluation.

Go to the contact form

Contact Us About Autopilot and Firmware

    Please fill out the message section as clearly and detailed as possible.

    Alternatively, you can send an email to [email protected].